E2H600

Bornemann E2H 600

Showing 1–16 of 57 results

add to enquiry (selected)

1 - 16 / 16

1 / 1

Picture Products (click for details:) Pos SKU Options Aktion
Two blue Fludyn BE2H 600 mono pumps without motor, mounted crosswise on a wooden pallet ready for despatch
Fludyn BE2H 600 mono pump
A complete replacement pump, suitable, for example, as a replacement for an ITT-Bornemann* E2H 600 progressing cavity pump
-
BEH800-600-2
Clear
Placeholder
Repair or full maintenance Bornemann E2H 600
We repair and overhaul your pump completely. All wearing parts are checked and replaced or repaired as necessary.
-
BEH999-600-2
A blue stator for Bornemann E2H 600 progressing cavity pumps or mono pumps. It is lying on its side and you can see the opening for the rotor on the left and the black elastomer inside.
Stator E2H 600
Stator for Bornemann E2H 600 progressing cavity pumps / mono pumps
22
BEH022-600-2
Clear
A coupling rod made of metal for E2H 600 progressing cavity pumps. It lies at an angle and you can see the connection for one of the joints on the front left.
Coupling rod E2H 600
Made in Germany and available in various metals and grades of hardness. Suitable for Fludyn BE2H 600 and ITT-Bornemann E2H 600 mono pumps.
11
BEH011-600-2
Clear
An E2H 600 metal rotor lies across a neutral background. On the left you can see the connection with which the eccentric screw is connected to the joint.
Rotor E2H 600
Rotor suitable for Bornemann progressive cavity pumps / mono pumps. The rotor is made in Germany and available in various materials.
10
BEH010-600-2
Clear
Placeholder
Mounting kit rotor E2H 600
Small parts for attaching the rotor to the joint
-
BEH900-600-2
The picture shows a joint for E2H 600 progressing cavity pumps. It is made of metal and is set diagonally against a neutral white background. In the middle you can see the black joint sleeve. The joint pin openings are sealed with yellow caps on both sides. On the left is the large opening for the rotor or coupling rod. It is also sealed with a white cap.
Joint E2H 600
The joint is pre-assembled and ready to use.
216
BEH216-600-2
The "mounting kit joint for E2H 600 mono pumps" contains various small parts that you should replace when installing a joint or a replacement joint. The photo shows 4 rubber rings (o-rings) in two different sizes. Plus 4 metal caps, two metal pins and two zyco sleeves.
Mounting kit joint E2H 600
Small parts for fitting a joint
216.1
BEH2161-600-2
Placeholder
Repair kit soft packing E2H 600
Contains all spare parts for replacing a stuffing box / soft packing.
-
BEH901-600-2
Placeholder
Mechanical seal E2H 600
Spare parts for replacing the mechanical seal
95
BEH095-600-2
Placeholder
Spare parts kit: stator + rotor E2H 600
Stator, rotor and small parts
-
BEH992-600-2
A drive shaft made of metal for E2H 600 progressing cavity pumps
Drive shaft E2H 600
Drive shaft suitable for Fludyn BE2H 600 and ITT-Bornemann* E2H 600 progressing cavity pumps / mono pumps.
12
BEH012-600-2
Clear
A blue-painted pump housing for E2H 600 progressing cavity pumps against a white, neutral background. It has a round inlet opening at the bottom. Two rectangular openings on the left and right for connecting the stator and bearing assembly.
Pump casing E2H 600
1
BEH001-600-2
A blue painted, empty bearing housing for E2H 600 progressing cavity pumps. It stands in front of a neutral white background. It has two feet at the bottom, e.g. for mounting on a base plate. On the left, you can see the opening for the drive shaft and the shaft seals.
Bearing casing E2H 600
2
BEH002-600-2
Placeholder
Stuffing box housing for E2H 600
3
BEH003-600-2
Placeholder
Stuffing box gland for E2H 600
4
BEH004-600-2
add to enquiry (selected)